SMBBR-AF-SMBBR组合工艺处理高氨氮农药废水

采用特异性移动床生物膜反应器(SMBBR)和厌氧生物滤池(AF)组合工艺处理高氨氮农药废水。考察了HRT、pH和DO等工艺条件对SMBBR-AF-SMBBR组合工艺运行稳定期COD和氨氮去除率的影响。试验结果表明,在进水COD为2 408~7 440 mg/L、ρ(NH_4~+-N)为160.21~433.84 mg/L、TN为208.27~537.65 mg/L、HRT为8d、pH为8.0、DO为4 mg/L的条件下,处理后出水平均COD为342 mg/L,COD去除率达92.3%;ρ(NH_4~+-N)小于4.0mg/L,氨氮平均去除率为89.2%;TN小于50 mg/L,平均TN去除达83.0%。出水各指标均优于原A2O工艺出水。     

珠江口表层水中多环芳烃的分布特征及健康风险评估

分别于2015年2、5、8、11月在珠江八大入海口采集表层水体样品,应用固相萃取富集法对该区域表层水体中16种USEPA优控多环芳烃(PAHs)的时空分布特征进行分析,并利用终生致癌风险增量模型(ILCR)对该区域的饮水健康风险进行评价。结果表明:珠江口4个季度所采集的水样中,∑15PAHs的浓度范围为18.0~50.3 ng/L,含量处于中等水平。其中7种强致癌性∑7PAHs的浓度范围为1.53~3.73 ng/L,占∑15PAHs的5.89%~11.1%,∑15PAHs和∑7PAHs在枯水期(2、11月)样品中明显高于丰水期(5、8月)。就组成特征而言,各采样点PAHs以3、4环为主。珠江口表层水中非致癌类PAHs的危害商数值为0.99×10~(-5)~2.73×10~(-5),远低于USEPA规定的阈值(1);致癌类PAHs产生的健康风险为6.50×10~(-8)~2.37×10~(-7),其中Ba P导致的饮水途径健康风险最高,所有点位致癌类PAHs的健康风险均低于USEPA推荐的对致癌物质最大可接受风险水平(10~(-6)),表明珠江口表层水中PAHs尚不具备严重的致癌风险,但是仍然存在潜在的健康风险,需要重点控制和管理。     

The associations of air pollution exposure during pregnancy with fetal growth and anthropometric measurements at birth: a systematic review and meta-analysis

Environmental Science and Pollution Research - Fetal growth has been demonstrated to be an important predictor of perinatal and postnatal health. Although the effects of maternal exposure to air...     

The accounting method and application of CO2 emissions responsibility by the electricity sector at the provincial level in China

When accounting the CO₂ emissions responsibility of the electricity sector at the provincial level in China,it is of great significance to consider the scope of both producers’ and the consumers’ responsibility,since this will promote fairness in defining emission responsibility and enhance cooperation in emission reduction among provinces.This paper proposes a new method for calculating carbon emissions from the power sector at the provincial level based on the shared responsibility principle and taking into account interregional power exchange.This method can not only be used to account the emission responsibility shared by both the electricity production side and the consumption side,but it is also applicable for calculating the corresponding emission responsibility undertaken by those provinces with net electricity outflow and inflow.This method has been used to account for the carbon emissions responsibilities of the power sector at the provincial level in China since 2011.The empirical results indicate that compared with the production-based accounting method,the carbon emissions of major power-generation provinces in China calculated by the shared responsibility accounting method are reduced by at least 10%,but those of other power-consumption provinces are increased by 20% or more.Secondly,based on the principle of shared responsibility accounting,Inner Mongolia has the highest carbon emissions from the power sector while Hainan has the lowest.Thirdly,four provinces,including Inner Mongolia,Shanxi,Hubei and Anhui,have the highest carbon emissions from net electricity outflow- 14 million t in 2011,accounting for 74.42% of total carbon emissions from net electricity outflow in China.Six provinces,including Hebei,Beijing,Guangdong,Liaoning,Shandong,and Jiangsu,have the highest carbon emissions from net electricity inflow- 11 million t in 2011,accounting for 71.44% of total carbon emissions from net electricity inflow in China.Lastly,this paper has estimated the emission factors of electricity consumption at the provincial level,which can avoid repeated calculations when accounting the emission responsibility of power consumption terminals（e.g.construction,automobile manufacturing and other industries）.In addition,these emission factors can also be used to account the emission responsibilities of provincial power grids.     

不同轮作模式下作物根际土壤养分及真菌群落组成特征

为研究宁夏中部干旱带不同轮作模式下土壤养分及真菌群落组成的特征,以谷子轮作大豆（MRG）、轮作籽粒苋（MRA）、轮作藜麦（MRQ）及谷子连作（CK）为对象,测定了土壤养分含量,并利用Illumina MiSeq高通量测序平台测定了土壤真菌的ITS变异区序列.结果表明,不同轮作模式对土壤养分的影响存在差异.3种轮作模式下土壤pH和电导率均有所下降,土壤全氮、全钾、全磷和有机质含量均上升,OTUs数和α多样性指数均高于连作.真菌群落组成研究结果显示,子囊菌门（Ascomycota）为4种模式下的优势菌群.聚类分析显示MRA和MRG的真菌属组成最为相似,其次是MRQ,CK与3种轮作模式相差较大.相关性分析显示,土壤养分与几种优势真菌属呈显著相关性（P<0.05或P<0.01）,土壤全氮、全钾、硝态氮和有机质含量是影响土壤真菌群落最主要的因子.主成分分析（PCA）表明,MRG轮作模式优于MRA和MRQ模式.综上所述,轮作提高了真菌群落多样性指数,改变了土壤真菌群落结构,改善了土壤肥力状况,其中以谷子与大豆轮作效果最佳,建议将谷豆轮作作为中部干旱带杂粮产业中主要的轮作模式之一进行推广.     

典型西南工业城市柳州市核心区大气污染物时空分布与气象因素研究

为研究柳州市核心区大气污染物浓度时空变化规律与气象因素之间的关系,统计分析了2018年全年研究区内6个自动监测站点PM_(2.5)、PM_(10)、SO_2、NO_2、O_3和CO的浓度监测数据和气象站气象数据,并对28次超标日污染物来源进行了解析.结果显示:①核心区颗粒污染物污染较为严重,且以PM_(2.5)为主的细颗粒污染物仍为柳州市主要的大气污染物;各污染物月均浓度季节差异显著,除NO_2外柳州大气污染物浓度下降明显,指示柳州市多项节能减排综合整治措施成效显著;PM_(2.5)、PM_(10)、CO受早晚高峰期影响,浓度日变化均呈双峰型;NO_2在不同季节峰型不同,作为O_3前体物其浓度日变化与O_3相反,呈现"早峰午谷"的变化趋势.②通过对污染物浓度插值发现,由于核心区主要工商业区位于西部且处于主导风向下风向,故PM_(2.5)和SO_2浓度西北高、东南低,PM_(10)、NO_2和CO浓度西南高、东北低;核心区东部的山区为O_3生成带来大量前体物,使O_3浓度东南高、西北低.③由于气候特征,核心区春、夏季主要气象因素均为降水量;秋季的主要气象因素是风速,风速与污染物的负相关关系表明了风的扩散效应;冬季大部分污染物与气象因素的相关性不显著,表明人为因素对污染物的影响大于气象因素;核心区大气污染物主要来源于局地排放和区域传输,且南北主导风向对大气污染影响最大.④HYSPLIT模型结果指示柳州超标日大气污染物主要来自于珠三角地区,且陆源颗粒物浓度普遍比海洋源高,来自南部的远距离输送气流颗粒物含量最低,表明远距离输送为影响颗粒物传播的主要原因.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Identification of potential electrotrophic microbial community in paddy soils by enrichment of microbial electrolysis cell biocathodes

Electrotrophs are microbes that can receive electrons directly from cathode in a microbial electrolysis cell (MEC). They not only participate in organic biosynthesis, but also be crucial in cathode-based bioremediation. However, little is known about the electrotrophic community in paddy soils. Here, the putative electrotrophs were enriched by cathodes of MECs constructed from five paddy soils with various properties using bicarbonate as an electron acceptor, and identified by 16S rRNA-gene based Illumina sequencing. The electrons were gradually consumed on the cathodes, and 25%–45% of which were recovered to reduce bicarbonate to acetic acid during MEC operation. Firmicutes was the dominant bacterial phylum on the cathodes, and Bacillus genus within this phylum was greatly enriched and was the most abundant population among the detected putative electrotrophs for almost all soils. Furthermore, several other members of Firmicutes and Proteobacteria may also participate in electrotrophic process in different soils. Soil pH, amorphous iron and electrical conductivity significantly influenced the putative electrotrophic bacterial community, which explained about 33.5% of the community structural variation. This study provides a basis for understanding the microbial diversity of putative electrotrophs in paddy soils, and highlights the importance of soil properties in shaping the community of putative electrotrophs.     

轻质高强多功能点阵夹层结构研究进展

根据材料类型和点阵结构,对点阵夹层结构进行了分类简述,并从静态、动态力学性能上,分析了各类点阵夹层结构的优缺点。简要叙述了设计过程中,综合考虑材料、结构以及功能等影响因素,针对不同使用工况的要求,可对各影响因素进行匹配设计,以实现传热特性、电磁波屏蔽特性、声学特性等不同的功能性需求。然后介绍了复合点阵夹层结构(嵌锁组装、模具热压成形、穿插编织)和金属点阵夹层结构(冲压成形、挤压线切割、拉伸网折叠、搭接拼装、熔模铸造以及增材制造)的主要制造工艺。最后提出如何将设计因子与多目标进行匹配及优化设计,是轻质高强点阵夹层结构的重点研究方向,轻质高强点阵夹层结构将朝多材料及多结构复合方向发展,开发新的制造工艺,提高费效比,是点阵夹层结构材料需解决的问题。     

低碳经济发展中物流绿色发展趋势研究

文中主要对低碳经济发展中物流绿色发展趋势进行了研究,介绍了对低碳经济发展物流绿色发展评价,探讨了低碳经济发展中的不同问卷的调查结果,对物流绿色发展的认知、态度和行动进行了论述,在论述过程中,主要包括对低碳经济发展中的物流认知、对低碳经济发展中的物流态度、对低碳经济发展中的物流行动和对发展低碳经济物流的认知、态度与行动的比较,最后给出了低碳经济发展中物流绿色发展趋势,对低碳经济发展中物流绿色发展给出了研究基础。